Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Fence Installation: The Los Angeles Owner’s Guide
Boral fence installation in Los Angeles typically runs $4,130 to $10,620 for a full panel and post replacement, depending on linear footage, post condition, and whether we’re pulling existing concrete or setting new footings. We stock Boral-compatible post brackets, rail connectors, and the stainless fasteners these composite fences actually need, and we can usually have a crew out within the week once we confirm your panel profile and post spacing. Most owners discover the problem when a panel starts sagging at the rail connection or a post shifts after rain, and by that point the original installation hardware has often been quietly corroding for two or three wet seasons.
If you’re staring at a leaning Boral panel right now, start by checking whether the post itself moves or just the panel. That single observation tells you whether you’re looking at a rail-mount repair or a footing replacement, and it changes the price meaningfully. We’ll walk through that below.
Which Boral Models This Applies To
Boral fencing in Los Angeles is built around a handful of composite profile lines: the Classic, Estate, and Sierra series are the ones we see most often in single-family yards from Silver Lake to the Valley, and each uses a slightly different rail channel and post bracket. The Classic panels sit flush with a visible top rail, the Estate panels have a deeper shadow line, and the Sierra series is the heaviest of the three, with posts that need a wider bracket and longer fasteners. The giveaway is usually stamped on the back of a panel near the bottom rail, but after years of sun and sprinkler exposure that stamp can fade. When it’s gone, we measure the panel thickness and the rail channel width with a caliper and match from there.
One thing worth knowing: Boral stopped manufacturing some of the Sierra post caps a few years back, so if you’ve got a Sierra fence from 2016 or earlier, aftermarket caps are sometimes the only option. They fit fine and hold up in Los Angeles sun as long as they’re UV-stabilized, but they’re not OEM. We carry both, and we’ll tell you which one we’re quoting before we order anything.
Styles & brands we work with
Signs Your Boral Fence Installation Is Failing
- A panel sags at the middle rail connection. This usually means the original installer used galvanized nails or generic screws instead of Boral’s stainless fasteners, and the hardware has finally corroded through. The panel itself is almost always fine; the connection failed first.
- The post wobbles when you push it, but the panel doesn’t move. That’s a footing problem, not a panel problem. In Los Angeles clay and decomposed granite, water pools around the post base after winter rain, and the concrete footing cracks or settles.
- You see white or chalky residue running down from a screw hole. That’s galvanic corrosion, and it means someone used the wrong metal against the composite. Once it starts, that screw is done and the surrounding material is weakened.
- The gate drags or won’t latch after a dry season. Composite posts expand and contract with temperature swings, and in Los Angeles the difference between an August afternoon and a December morning is enough to shift a gate 3/8 of an inch. The hinge pack wasn’t adjusted for that range.
- A panel cracked along the bottom edge near a sprinkler head. Composite doesn’t rot, but constant irrigation spray against the bottom rail encourages mineral buildup and can stress the material over several seasons. We re-set the panel with a small gravel gap instead of direct soil contact.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
For Los Angeles homeowners, a Boral fence installation with new posts, footings, and panels lands between $4,130 and $10,620. The low end of that range covers a shorter run, say 30 to 40 linear feet, where the existing post footings are sound and we’re reusing the post locations. The high end covers 80 to 100 linear feet, new concrete footings for every post, and a gate with adjustable hinges. The biggest cost driver is almost always the footing work: if we’re chipping out existing concrete and hauling it away, that’s labor and disposal.
Every Boral fence installation we quote includes a written price before any work starts, the stainless fasteners, post brackets, concrete, panel-to-post alignment, and a photo of the clean-up before the crew leaves. The workmanship is covered by our 365-Day Done Right Promise: if something isn’t right after the job is done, we make it right. As Graham Stein puts it, “The written scope is the promise; if it is not on the paper, we have not agreed to it yet.”
DIY or Call Us?
You can absolutely replace a single Boral panel yourself if the posts are solid, the rails are intact, and you have a second pair of hands. The panel lifts out of the rail channel once you remove the retaining screws, and an afternoon with basic tools can get it done. What you shouldn’t attempt is resetting a post in Los Angeles soil without understanding what’s under it: gas lines, irrigation pipes, and old foundation remnants are common in older neighborhoods like Los Feliz and West Adams, and a digging bar through a gas line is not a trade-off anyone wants to make to save a few hundred dollars.
For post work, rail repair, or gate re-hanging where the hinge pack has failed, call us. Our crews have done this on Boral fences from Pasadena to Santa Monica, and we bring the right fasteners the first trip. Call (949) 850-9896 and tell us what you’re seeing; we’ll tell you honestly whether it’s a homeowner fix or a crew visit.
FAQs
A properly installed Boral fence in Los Angeles lasts 20 to 25 years, with panels often outlasting the original hardware. The composite itself doesn’t rot or attract termites, but the fasteners and post footings are the weak points, especially in sprinkler-irrigated yards and clay-heavy soil. If your fence is under 10 years old and failing, the installation was likely the issue. Call (949) 850-9896 for an honest assessment.
Yes, and we do this often. If the posts and rails are sound, we replace just the damaged panel and its retaining hardware, which keeps the job well under the full-installation range. The trick is matching the profile and color, since Boral’s shade batches varied slightly across production years. We’ll bring a sample against your existing fence before we order.
Most Boral fence installation jobs in Los Angeles take one to two days. A single post reset with a new footing needs a day, and a full run with new footings and a gate runs two days including the concrete cure time before we hang panels. We schedule around family rest hours where possible, and the crew uses quiet tools during nap and school hours.
We stock the common rail connectors, post brackets, and stainless fasteners for Classic and Estate series fences on our trucks. Sierra-series post caps and full panel replacements often come from our supplier’s Los Angeles warehouse within a few days. The fastest way to know is to send us a photo of the damaged part; Graham can usually identify it from one image. Call (949) 850-9896 with a picture ready.
If you need a Boral fence installation in Los Angeles, call us at (949) 850-9896 to schedule a free estimate. We’ll come out, measure the fence, check the post footings, and hand you a written price before any work starts. We’re an independent fencing contractor, not affiliated with Boral, and we also work with fencing and building products from KraftMaid, Cambria, and Silestone across our remodeling projects. Our team at Elmstead Remodeling, a Cedarwell company, runs every job with the Cedarwell Care Promise: drop cloths on the floors, shoe covers at the door, a photo of the clean-up before we leave, and quiet tools during family rest hours. We’ve been serving Los Angeles and nearby areas since 2005.
Written by Graham Stein, Owner, Elmstead Remodeling at Elmstead Remodeling, serving Los Angeles and nearby areas.
