Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Boral Kitchen Remodeling: The Los Angeles Owner’s Guide
If you own a home in Los Angeles with Boral kitchen materials and something has failed, you’re probably looking for a straight answer on replacement cost and timing. A full Boral kitchen remodel in Los Angeles typically runs $16,520 to $53,100 depending on cabinet count, countertop square footage, and whether you’re replacing surfaces or rebuilding layout. Most owners call us after a specific part fails: a cracked Boral countertop edge, a delaminating cabinet door facing, or a sink base showing water damage from a failed seal. Here’s what we know about matching Boral materials, what it costs, and how we handle the work in your home.
Which Boral Models This Applies To
Boral has shifted its product lines over the years, which matters when you’re trying to match an existing kitchen. The Boral products most often seen in Los Angeles homes are the pressed-wood cabinet doors and drawer fronts from the mid-2000s through the late 2010s, along with Boral’s composite stone and cultured stone countertops that were popular in tract homes and mid-range remodels across the San Fernando Valley, Westside, and Pasadena areas.
The compatibility issue we run into regularly is this: Boral cabinet box sizes did not stay consistent across their manufacturing years. A 2008 Boral cabinet door from a home in Sherman Oaks is not guaranteed to match a 2015 door, even if both are the same width and height on paper. The hinge cup depth and the edge profile changed slightly, which means what looks like a “same size” swap can leave a visible gap or a door that doesn’t sit flush. We always measure the hinge cup bore and the door edge profile on-site before ordering anything.
For countertops, Boral’s composite stone came in a few standard thicknesses: 12mm, 20mm, and 30mm. If you’re replacing a cracked section of a Boral countertop in a Los Angeles kitchen, you need to know which thickness you have. We’ve seen homeowners in Glendale and Burbank order a 20mm slab to patch a 30mm island and end up with a lip that catches every plate they set down. We verify thickness first, then match.
Elmstead Remodeling is an independent remodeling contractor, not affiliated with Boral. What that means for you: we source Boral-compatible materials and quality equivalents, but we’re not bound to a single vendor’s inventory. When Boral discontinued certain lines, we found dependable aftermarket sources for door fronts and edge profiles that match the originals. Where an OEM Boral part still exists, we quote it. Where it doesn’t, we tell you that plainly and show you the aftermarket option with the same profile and finish.
Styles & brands we work with
Signs Your Boral Kitchen Remodeling Is Failing
- Cabinet door edges are swelling or delaminating near the sink or dishwasher. This is the most common Boral failure we see in Los Angeles kitchens. The pressed-wood core absorbs moisture through any micro-crack in the edge banding. What starts as a hairline split becomes a soft, swollen edge within a season. Cause: edge banding failure plus Southern California’s humidity swings.
- Countertop seam is lifting or you can feel a ridge where two slabs meet. Boral composite stone seams were often set with polyester adhesive, which breaks down over time with heat cycling. Los Angeles kitchens with south-facing windows see more thermal expansion than shaded rooms. A seam that’s visibly lifted is a failure point, not a cosmetic issue.
- Drawer fronts are pulling away from the drawer box. The attaching screws on Boral drawer fronts were sometimes driven into particleboard without enough thread depth. After years of opening and closing, especially in a busy household with kids, the front starts to wobble and then separates. We fix this with a stronger mechanical connection, not just more glue.
- Faucet base or sink rim is corroded and the counter around it is darkening. Los Angeles tap water has mineral content that accelerates corrosion on cheaper metal components. If the counter under your faucet is darkening, water has been sitting there. That is a seal failure and it will only spread.
- Hinges on Boral cabinet doors are sagging or the doors no longer line up evenly. The hinge cup wears first, then the mounting screw holes in the compressed panel. If one door in a row is suddenly lower than its neighbor, the hinge is failing. Left alone, the stress transfers to the cabinet face and you get a split.
Replacement Cost & What’s Included
Here’s what we charge in Los Angeles for Boral kitchen remodeling work, installed:
- Cabinet door and drawer front replacement (Boral-compatible): $4,720 – $15,340 depending on door count and finish
- Countertop replacement (Boral composite stone or quality equivalent: Cambria, Silestone, Caesarstone): $2,360 – $7,670 installed, based on square footage and thickness
- Backsplash replacement around Boral countertop work: $945 – $2,950
- Kitchen island rebuild or reskin: $3,540 – $11,800
- Full Boral kitchen remodel (cabinets + counters + fixtures + labor): $16,520 – $53,100
What drives the range: whether we’re matching existing Boral pieces or pulling and replacing full sections, the linear feet of countertop, the number of cabinets, and whether the plumbing fixtures (Kohler, Moen, or Grohe) are being reused or replaced. Every quote includes the written line-item price before any work starts. If it’s not on the paper, we haven’t agreed to it yet. That’s the rule on every Elmstead job, no exceptions.
See the difference
Before
After
Before
After
Before
AfterDIY or Call Us?
Cabinet doors and countertops are not intrinsically dangerous to handle, so there are a few things an owner can safely check. You can tighten hinge screws, you can clean the edge banding and inspect for cracks, and you can measure your existing Boral pieces to compare against specs we confirm on a call. That information helps us quote faster and protects you from ordering the wrong part.
Where DIY goes wrong: adhesive bonding on composite stone, seam setting, and any countertop overhang work. A 30mm Boral countertop section is heavy, and the edging compounds used in production are not the stuff from the hardware store. Get the adhesive wrong and the seam fails in six months. Also, when a Boral cabinet hinge has wallowed out its hole, drilling more holes next to it weakens the panel further. We see attempted fixes in Los Angeles kitchens all the time that double the eventual repair cost.
If you’re not sure whether your Boral kitchen issue is a quick swap or a bigger problem, call us at (949) 850-9896. We’ll walk through what you’re seeing, and if we can save you a service visit with a measurement or a photo, we will.
FAQs
Boral kitchen components typically last 12 to 20 years in Los Angeles, depending on sun exposure, proximity to the sink or dishwasher, and how consistently spills are addressed. Cabinets near heat sources or south-facing windows fail sooner. Countertops with failed seams can go bad in under a decade if water reaches the substrate. Call (949) 850-9896 and we’ll assess what you have.
In some cases, yes. A hairline edge crack with no swelling can be resealed and color-matched. A delaminating door core cannot be reliably glued back, because the substrate absorbs the adhesive and fails again. We will tell you honestly if a repair will hold or if you’re paying for a temporary patch. Call (949) 850-9896 for a straight assessment.
Cabinet door and drawer front replacement takes two to three days. A full countertop replacement in a Los Angeles kitchen runs three to five days including template, fabrication, and install. A full kitchen remodel runs three to six weeks depending on plumbing, electrical, and permitting. We schedule around your family’s quiet hours where we can. Call (949) 850-9896 for a timeline on your specific project.
We keep common hinge types, edge banding profiles, and mounting hardware on our trucks for immediate fixes. Full cabinet doors, drawer fronts, and composite stone slabs are ordered per job with exact measurements, because Boral sizing changed across manufacturing years and we won’t guess. For specific Boral-compatible pieces, call (949) 850-9896 and we’ll confirm what we can pull from stock versus what we order.
No. The written price is given before any work begins and it does not grow after the crew arrives. If we open a wall and find something we couldn’t have seen, we stop, explain it, and give you a written change order before proceeding. You approve the number before we touch it. That’s the Cedarwell Care Promise and it’s how Graham Stein has always run jobs.
Call Elmstead Remodeling for Boral Kitchen Work in Los Angeles
If you have a Boral kitchen part that failed, we’ll match it, price it in writing, and install it cleanly. We run shoe covers and drop cloths on every job, we ask before moving anything on your counters, and we photograph the clean-up before the crew leaves. We work with families in Los Angeles who have kids and pets, and we schedule around nap hours and school runs where the job allows. Call (949) 850-9896 for your free estimate, and we’ll walk you through exactly what we’d do before anything is signed.
Written by Graham Stein, Owner, Elmstead Remodeling at Elmstead Remodeling, serving Los Angeles and nearby areas.
